-
Who this checklist is for
-
Step 1: Write down your actual operating conditions — all of them
-
Step 2: Get the real performance curve, not the brochure number
-
Step 3: Match the metallurgy to the gas, not the temperature
-
Step 4: Ask "what's NOT included" before you ask the price
-
Step 5: Check references — then actually call them
-
Step 6: Put the acceptance test standard in writing — before you sign
-
Step 7: Run the 10-year cost, not the purchase price
-
Two things I wish I had done from the start
Who this checklist is for
If you are sourcing an industrial centrifugal compressor — for a process line, a plant utility system, or high-pressure air — and you are not a rotating equipment engineer or a full-time procurement specialist, bookmark this page. I have handled compressor sourcing orders for 9 years. I have personally made (and documented) 5 significant mistakes, totaling roughly $47,000 in wasted budget and a few months of timeline. Now I maintain our team's pre-purchase checklist.
The 7 steps below are what that checklist looks like. No theory. Just the checks I run on every order.
Step 1: Write down your actual operating conditions — all of them
This sounds basic. It is not.
In 2019, I bought a high-pressure centrifugal air compressor. The spec sheet numbers looked fine. Flow, pressure, power — all in range. We installed it. Performance was short from day one.
Why? Our plant sits at 1,200 meters elevation. I never applied an elevation correction to the flow and pressure I sent out. The vendor's curve was based on sea-level conditions. That was on me, not them.
Result: $8,400 in re-selection costs, 6 weeks of delay, and a very uncomfortable meeting.
Before you contact any supplier, write down: inlet temperature, pressure, and relative humidity. Altitude, plus corrected conditions. Gas composition (including any contaminants, if it is not just air). Flow range — not just design point, but minimum and maximum. And pressure units. bar(a), bar(g), psi. These get mixed up more often than you would think.
This is the step most people skip in sourcing. They jump straight to the spec sheet. Then they chase the curve later.
Step 2: Get the real performance curve, not the brochure number
Every centrifugal compressor has a performance curve. The brochure gives you the design point. You need the full curve across your range — from surge line to choke line.
Ask for the curve. Compare curves. If a supplier will not send one, walk away regardless of how low the quote looks.
The most common trick I have come across: the brochure says "100 m³/min at 8 bar," but the curve shows that flow drops to 80 m³/min once inlet temperature hits above 35°C. If you are buying this for a process, that is a production problem, not a rounding error.
Step 3: Match the metallurgy to the gas, not the temperature
I am not a metallurgist, so I cannot speak to the specific metallurgy selection questions. What I can tell you from a procurement perspective is this: the material selection cannot be driven by temperature rating alone.
In 2021, we sourced a unit for wet sour gas duty. The temperature was well within spec. But the impeller was standard stainless steel. 18 months later, we had pitting and a $12,200 rebuild.
What works: send your full gas composition — including trace H2S, CO2, moisture, and chlorides — to the supplier and ask their process engineer to confirm material selection in writing. Do not accept "standard material is fine." Get it signed.
Step 4: Ask "what's NOT included" before you ask the price
This one is flat-out important.
I have learned to ask "what's not included" before "what's the price."
The vendor who lists all fees upfront — even if the total looks higher — usually costs less in the end. A quote that looks 15% cheaper can add options later: baseplate, coupling, gearbox, lube oil console, coolers, control panel, and field commissioning. All listed as "optional."
I got burned by this in 2022. The quote looked clean. By the time we placed the order, it came out $9,000 more than the next-highest bid. I am not saying the supplier was malicious. Their quote was structured that way. It was my responsibility to ask.
Now I run every RFQ with an "included, please confirm" list:
- Skid, grouting, anchor bolts
- Coupling and gearbox
- Lube oil system and oil cooler
- Inlet filter, silencer, expansion joint
- Control panel, PLC, DCS interface
- Field commissioning, start-up, operator training
- Sea freight, insurance, import duties
Step 5: Check references — then actually call them
Every supplier has references. Most are hand-picked. That is fine. But you have to make the calls.
Ask three specific questions:
- Did the unit hit the rated performance point at the time of purchase? If not, by how much?
- What was the uptime in the first 24 months?
- If you were buying again today, would you select this vendor? Why or why not?
The good news: this usually works. Nobody refuses a reference call. If you get hedging, that is your answer.
Step 6: Put the acceptance test standard in writing — before you sign
This is the one that protects you from a "close enough" unit.
There are standards for how a centrifugal compressor gets performance-tested. API 617 (for centrifugal compressors in petroleum, chemical, and gas service) and ASME PTC 10 define how the test runs and what tolerances apply. If you do not cite a standard, the supplier will test however is convenient.
I went through an acceptance dispute in 2023. Their test report showed performance "within tolerance." Their tolerance. We used a different basis. Because the contract had no standard named, we had to negotiate — and ended up with an $8,000 concession and a 2-week delay.
Put the test standard name, tolerance percentage, and test location in the contract. Add: what happens if performance is short of the rated point? Make it enforceable.
Step 7: Run the 10-year cost, not the purchase price
This last step is where I hesitated the most in my early days.
Late 2023: two quotes for a high-pressure centrifugal compressor. One from an established manufacturer. One from a newer, lower-cost bidder. First quote: $86,000. Second: $71,000.
I went back and forth for two weeks. On paper, the cheaper option made sense. But my gut said the delta was too small to justify the reference gap for a process running year-round. The upside was $15,000 in savings. The risk was unplanned downtime that could cost $20,000–$30,000 in production loss per event.
So I ran the 10-year cost. Energy (at your actual tariff, not the brochure rate). Planned maintenance and consumables. Unplanned downtime (industry averages 2–5% per year for this class). Major overhaul intervals.
The established unit had a 5% higher thermal efficiency. At 8,000 operating hours per year and $0.12/kWh, that 5% closed the $15,000 gap in about 6 years. Combined with the downtime risk, I went with the more expensive one. The quieter one.
I chose peace of mind over savings, that time. It worked out. But I do not think that is always the right call. If the unit is standby duty or low load, the cheaper option may be the better math. Same calculation. Different variables.
Two things I wish I had done from the start
First: build a pre-purchase checklist. I only created mine after the third order. If I had done it before the first one, it would have saved about $30,000.
Second: walk through Step 1 and Step 3 with your process engineer and get it signed off. Not verbally. Signed.
None of this is deep technical expertise. Running through these steps in order is the difference between a sourcing story you tell and a sourcing mistake you nurse. Simple as that.
If you want to check your sourcing list against ours, or your operating conditions are unusual, reach out to our team at Centrifugal Compressor Sourcing.